Cross-linking epoxide resins with hydrolysates of chrome-tanned leather waste

Differential scanning calorimetry was employed to investigate the reaction of diglycidyl ethers of bisphenol A (DGEBA) of mean molecular mass 348–480 Da, with collagen hydrolysate of chrome-tanned leather waste in a solvent-free environment. The reaction leads to biodegradable polymers that might facilitate recycling of plastic parts in products of the automotive and/or aeronautics industry provided with protective films on this basis. The reaction proceeds in a temperature interval of 205–220°C, at temperatures approx. 30–40°C below temperature of thermal degradation of collagen hydrolysate. The found value of reaction enthalpy, 519.19 J g⁻¹ (= 101.24 kJ mol⁻¹ of epoxide groups) corresponds with currently found enthalpy values of the reaction of oxirane ring with amino groups. Reaction heat depends on the composition of reaction mixture (or on mass fraction of diglycidyl ethers in the reaction mixture); proving the dependence of kinetic parameters of the reaction (Arrhenius pre-exponential factor A (min⁻¹) and activation energy E _a (kJ mol⁻¹)) did not succeed. Obtained values of kinetic parameters are on a level corresponding to the assumption that reaction kinetics is determined by diffusion.     

Highly sensitive catalytic determination of molybdenum

A novel, highly sensitive, selective, and simple kinetic method was developed for the determination of Mo(VI) based on its catalytic effect on the oxidation of 1-amino-2-naphthol-4-sulfonic acid (ANSA) with H₂O₂. The reaction was followed spectrophotometrically by tracing the oxidized product at 465 nm after 30 min of mixing the reagents. The optimum reaction conditions were: 10 mmol l⁻¹ ANSA, 50 mmol l⁻¹ H₂O₂, 100 mmol l⁻¹ acetate buffer of pH 5.0 ± 0.05 and at 40 °C. Addition of 200 μg ml⁻¹ diethylenetriaminepentaacetic acid (DTPA) conferred high selectivity for the proposed method. Following the recommended procedure, Mo(VI) could be determined with a linear calibration graph up to 2.5 ng ml⁻¹ and a detection limit, based on the 3S_b-criterion, of 0.027 ng ml⁻¹. The unique sensitivity and selectivity of the implemented method allowed its direct application to the determination of Mo(VI) in natural and industrial waste water. The method was validated by comparison with the standard ETAAS method. Moreover, published catalytic-spectrophotometric methods for the determination of molybdenum were reviewed.     

Simultaneous screening and determination eight phthalates in plastic products for food use by sonication-assisted extraction/GC-MS methods

Studies on determination of eight kinds of phthalates, e.g. di-ethyl phthalate (DEP), di-propyl phthalate (DPP), di-isobutyl phthalate (DIBP), di-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-cyclohexyl phthalate (DCHP), di-(2-ethylhexyl) phthalate (DEHP), di-octyl phthalate (DOP), in 25 kinds of plastic products for food use, including packaging bags, packaging film, containers, boxes for microwave oven use, sucking tubes, spoons, cups, plates, etc. by gas chromatography in combination with mass spectrometry detector (GC-MS) in electronic ionisation mode (EI) with selected-ion monitoring (SIM) acquisition method (GC-MS (EI-SIM)) have been carried out. Methods have been developed for both qualitative and quantitative analysis of phthalates. Extraction, clean-up and analysis procedure have been optimized. Determination of samples were performed after frozen in liquid nitrogen and sonication-assisted extraction with hexane, clean-up with LC-C18 SPE and analyzed by GC-MS methods. The base peak (m/z = 149) of all the phthalates was selected for the screening studies. The characteristic ions, 121, 177, 222 for DEP; 191, 209 for DPP; 57, 223 for DIBP; 104 for DBP; 91, 132, 206 for BBP; 55, 167 for DCHP; 113, 167, 279 for DEHP; 279 for DOP were chosen for quantitative studies. These techniques are possible to detect phthalates at the level of 10.0 μg/kg. Overall recoveries were 82-106% with R.S.D. values at 3.8-10.2%. Only one of the 25 examined samples was free from phthalates. The rest 24 samples were found to contain at least three or more of these phthalates. The predominant phthalate detected in the studied samples was DEHP.     

The optimization of silica gel synthesis from chemical bottle waste using response surface methodology

To reduce the amount of hazardous chemical bottle waste in the environment, we report the optimization research of silica extraction in chemical bottle waste into silica gel. Alkali fusion and sol–gel process were utilised to prepare silica gel effectively. The alkali fusion process was carried out by adding sodium hydroxide to produce sodium silicate. Afterwards, silica gel was prepared by the sol–gel method using hydrochloric acid. Box-Behnken Design (BBD) was applied to Optimisation factors the poptimiseactors affecting the silica recovery. The factors that optimised mass ratio, particle size, and temperature. The optimum recovery of silica gel was obtained by SiO₂: NaOH mass ratio of 1:3, the particle size of 63–74 µm, and a temperature of 800 °C. The purity of silica gel optimum is 63.74% characterised using X-ray fluorescence. The structure of silica gel is the appearance of amorphous peaks at 2θ 20-30° characterised using an x-ray diffractogram. The silica gel surface was characterises using scanning electron microscopy-energy dispersive x-ray. It showed an irregular surface and characteristic showed that silica gel had a radius of 15.74 nm and a specific surface area of 297.08 m².     

Treatment of dairy wastewater using a selected bacterial isolate, Alcaligenes sp. MMRR7

Physicochemical and biologic analysis of dairy wastewater showed that the effluent had a high organic load (chemical oxygen demand [COD]: 5095 mg/L), an acidic pH (6.4), and a high probability of coliforms (most probable number [MPN]>1100). The various bacterial strains isolated and purified were identified as Sporolactobacillus sp., Citrobacter sp., Pseudomonas sp., Alcaligenes sp., Bacillus sp., Staphylococcus sp., and Proteus sp., as per the Bergey’s manual of systematic bacteriology. Among the five selected bacterial strains, the strain designated as MMRR₇ and identified as Alcaligenes sp. was found to give a maximum reduction in COD (62%) in 5 d of incubation. Chemical coagulation using alum at a concentration of 0.5 g/100 mL was found to be effective in the primary treatment of the effluent. Studies on free-cell treatment of the coagulated effluent with the selected bacterial strain Alcaligenes sp. MMRR₇ gave a maximum COD reduction of 91% in 120 h. This study clearly indicates the possibility of using Alcaligenes sp. MMRR₇ for the effective treatment of dairy wastewater.     

甲基绿－萃取光度法测定锑

本文用Ｃｅ（ＳＯ＿４）＿２作氧化剂，在６ｍｏｌ／Ｌ　ＨＣｌ溶液中将Ｓｂ（Ⅲ）氧化为Ｓｂ（Ⅴ），过量的氧化剂用盐酸羟胺还原，生成的［ＳｂＣｌ＿６］￣－与甲基绿形成离子缔合物，在２ｍｏｌ／ＬＨＣｌ溶液中被ＣＨＣｌ＿３萃取。Ｔｌ、Ｉｎ、Ｇａ、Ａｕ等２０种离子共存时不干扰测定，用于金属镉及废水中测定微量锑，结果满意。     

Design of a combined ozone/electron beam process for waste water and economic feasibility of the process

A design of a combined ozone/electron beam irradiation process for treating a 50 m³/h waste water stream from a molasses processing is discussed. Moreover, a cost evaluation of such a process in comparison to a conventional ozonation/biology treatment process has been performed to assess the potential of the irradiation process for technical use. Although the result of this comparison is not bad for the irradiation process an implementation into a full scale plant would not seem to be the thing to do in the present case.     

Degradation-fragmentation of marine plastic waste and their environmental implications: A critical review

This review critically evaluates the plastic accumulation challenges and their environmental (primarily) and human (secondarily) impacts. It also emphasizes on their degradation and fragmentation phenomena under marine conditions. In addition, it takes into account the leachability of the various chemical substances (additives) embedded in plastic products to improve their polymeric properties and extend their life. Regardless of their effectiveness in enhancing the polymeric function of plastic products, these additives can potentially contaminate air, soil, food, and water. Several findings have shown that, regardless of their types and sizes, plastics can be degraded and/or fragmented under marine conditions. Therefore, the estimation of fragmentation and degradation rates via a reliable developed model is required to better understand the marine environmental status. The main parameter, which is responsible for initiating the fragmentation of plastics, is sunlight/UV radiation. Yet, UV- radiation alone is not enough to fragment some plastic polymer types under marine conditions, additional factors are needed such as mechanical abrasion. It should be also mentioned that most current studies on plastic degradation and fragmentation centered on the primary stages of degradation. Thus, further studies are needed to better understand these phenomena and to identify their fate and environmental effects.     

The use of Agrobacterium tumefacients immobilized on Amberlite XAD-4 as a new biosorbent for the column preconcentration of iron(III), cobalt(II), manganese(II) and chromium(III)

A microorganism Agrobacterium tumefacients as an immobilized cell on a solid support was presented as a new biosorbent for the enrichment of Fe(III), Co(II), Mn(II) and Cr(III) prior to flame atomic absorption spectrometric analysis. Amberlite XAD-4 was used as a support material for column preconcentration. Various parameters such as pH, amount of adsorbent, eluent type and volume, flow rate of sample solution, volume of sample solution and matrix interference effect on the retention of the metal ions have been studied. The optimum pH for the sorption of above mentioned metal ions were about 6, 8, 8 and 6, respectively. The loading capacity of adsorbent for Co(II) and Mn(II) were found to be 29 and 22 μmol g⁻¹, respectively. The recoveries of Fe(III), Co(II), Mn(II) and Cr(III), under the optimum conditions were found to be 99 ± 3, 99 ± 2, 98 ± 3 and 98 ± 3%, respectively, at the 95% confidence level. The limit of detection was 3.6, 3.0, 2.8 and 3.6 ng ml⁻¹ for Fe(III), Co(II), Mn(II) and Cr (III), respectively, by applying a preconcentration factor of 25. The proposed enrichment method was applied for metal ion determination from water samples, alloy samples, infant foods and certified samples such as whey powder (IAEA-155) and aluminum alloy (NBS SRM 85b). The analytes were determined with a relative error lower than 10% in all samples.     

Characteristics of major dioxin/furan congeners in melted slag of ash from municipal solid waste incinerators

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in slag of fly ash from three municipal solid waste (MSW) incinerators were analyzed to observe any changes in characteristics and distribution of their congeners by melting process. Actual concentration and Toxic Equivalent (TEQ) concentration profiles of 17 major congeners of PCDDs/PCDFs for gas, fly ash and melted slag were compared. The distributions of PCDDs/PCDFs in different streams macroscopically showed similarities with the generally known profiles for emission gas from a municipal waste incinerator. The total concentrations of PCDDs/PCDFs in off-gas and fly ash have been known to be a function of incineration conditions and of air pollution control device utilization; however, their normalized distributions were independent of such conditions. The concentrations of PCDDs/PCDFs in the melted slag of fly ash were not related to the concentrations of PCDDs/PCDFs congeners in fly ash but were rather a function of the melting furnace type and operation. The total amount of PCDDs/PCDFs in the melted slag of fly ash contained almost 150–27,000 times less dioxin than that in fly ash, however, the TEQ of dioxin in the slag was reduced by 435–43,500 times, which could enable them to be utilized as recycled construction materials. In normalized TEQ concentration profiles of 17 congeners of PCDDs/PCDFs, the ratio of PCDFs to PCDDs changed from 1.32 to 2.19 by melting, which showed relatively higher portion of furans left in melted slag than those in fly ash. By comparing reduction ratios of different congeners, PCDDs (dioxins) were relatively easier to destruct than PCDFs (furans) during melting process. The most difficult congener to destruct could be octa-chlorinated dibenzofuran (OCDF) among major congeners. For slag cooling methods, dioxin concentration in TEQ of slow cooled slag by air was four times higher than that of fast cooled slag by water. Thus cooling by water is more appropriate with the added beneficial effect of producing granules/particles, which can be utilized as roadbed materials.